EMERSON SE4006P2 S-Series Dual Serial Interface Card DeltaV DCS (Hardware PN KJ3241X1-BK1)

Manufacturer: EMERSON (DeltaV Automation Solutions, formerly Fisher-Rosemount)

Part Number: SE4006P2 (internal hardware code KJ3241X1-BK1; S-series simplex serial communication module, redundant counterpart SE4036P2)

Product Type: Dual isolated serial communication interface FBM-style I/O card for DeltaV S-series DCS, protocol gateway bridging DeltaV controller with Modbus RTU/ASCII, DH+ and third-party serial field devices, supports simplex or 1:1 master-tracker hot redundant rack deployment

Matching Platform: Emerson DeltaV S-series DCS, S-series M5/M6 controllers, 8-wide I/O carrier rack, dedicated serial terminal block, all S-series analog/discrete I/O modules, DeltaV operator workstation, plant-wide control network

Core Function: Two independent galvanically isolated serial communication ports; each port configurable RS232, RS422 half/full duplex, RS485 half/full duplex; baud rate auto detection 300bps ~ 115200bps; factory preloaded Modbus RTU/ASCII driver, optional DH+/custom serial protocol licenses; each port configurable as Modbus master or slave; per-port surge & ESD isolation protection; built-in comprehensive bus fault diagnosis (cable break, slave offline, baud mismatch, communication timeout); dual redundant backplane bus to DeltaV controller; millisecond bumpless hot redundant switchover when paired with second SE4006P2 + redundant terminal block; front panel multi-color LED indicators for POWER, RUN, PORT1, PORT2, FAULT; ISA S71.04 Class G3 airborne contaminant rated PCB; conformal coating optional for Class I Div2 / Zone2 hazardous industrial areas; single-width S-series slot, hot-swap replaceable without full rack shutdown

1. Product Overview

SE4006P2 belongs to Emerson DeltaV S-series serial interface communication card family, serving as a dedicated serial protocol gateway to connect legacy serial field instruments, variable frequency drives, remote I/O stations and third-party PLCs to DeltaV distributed control system. Different from analog/digital I/O cards, it focuses on multi-protocol serial data conversion and bidirectional data mapping between DeltaV control database and external serial slave devices. Equipped with two fully electrically isolated serial ports, each channel works independently without signal crosstalk. The card comes pre-installed with standard Modbus RTU/ASCII driver out of factory, supporting master-slave mode switching for each port; additional software drivers for Allen-Bradley Data Highway Plus (DH+) are available via DeltaV software license. Automatic baud rate identification eliminates manual speed configuration errors during site commissioning, covering all mainstream industrial serial transmission rates from 300bps up to 115.2kbps. Integrated multi-layer self-diagnosis logic continuously monitors serial bus hardware faults including open wiring, short circuit, offline slave nodes, mismatched baud rate and communication timeout; all fault alarms and historical event logs are timestamped and uploaded to DeltaV operator HMI synchronously with front panel LED status lights, enabling field maintenance staff to rapidly locate communication failures without extra test instruments. Two deployment modes supported: simplex single SE4006P2 for non-critical auxiliary serial equipment; 1:1 redundant pair (two SE4006P2 plus matching redundant serial terminal block) for critical production serial control loops. Redundant card pair runs synchronous parallel scanning of serial bus segments; once primary communication card fails, standby tracker takes over all Modbus/DH+ data transmission within milliseconds with zero data loss and no process output bump, eliminating single-point communication failure risk for furnace drives, compressor serial transmitters and remote skid control equipment. Backplane adopts dual redundant high-speed bus communication with DeltaV S-series controllers; compact single-width slot design saves rack space, matched with dedicated shielded serial cable and special serial termination block for standardized cabinet marshalling wiring. The PCB complies with ISA S71.04 Class G3 harsh industrial standard, resisting dust, high humidity and trace chemical vapor corrosion; optional IPC-CC-830 anti-salt-fog conformal coating is provided for offshore oil & gas Zone2 hazardous control rooms. SE4006P2 is mature legacy DeltaV S-series hardware, still widely used as maintenance spare parts for aging power, petrochemical and chemical plant DeltaV DCS renovation and expansion projects.

Write a review

Your Name

Your Review

Rating

Continue